 |
Siphon Regulator 1.0
Nanosattelite attitude determination and control system.
|
Loading...
Searching...
No Matches
|
Siphon Regulator 1.0
Nanosattelite attitude determination and control system.
|
HAL configuration file. More...
#include "stm32f1xx_hal_rcc.h"#include "stm32f1xx_hal_gpio.h"#include "stm32f1xx_hal_exti.h"#include "stm32f1xx_hal_dma.h"#include "stm32f1xx_hal_cortex.h"#include "stm32f1xx_hal_flash.h"#include "stm32f1xx_hal_pwr.h"#include "stm32f1xx_hal_spi.h"#include "stm32f1xx_hal_uart.h"Go to the source code of this file.
Macros | |
| #define | HAL_MODULE_ENABLED |
| This is the list of modules to be used in the HAL driver. | |
| #define | HAL_DMA_MODULE_ENABLED |
| #define | HAL_GPIO_MODULE_ENABLED |
| #define | HAL_SPI_MODULE_ENABLED |
| #define | HAL_UART_MODULE_ENABLED |
| #define | HAL_CORTEX_MODULE_ENABLED |
| #define | HAL_DMA_MODULE_ENABLED |
| #define | HAL_FLASH_MODULE_ENABLED |
| #define | HAL_EXTI_MODULE_ENABLED |
| #define | HAL_GPIO_MODULE_ENABLED |
| #define | HAL_PWR_MODULE_ENABLED |
| #define | HAL_RCC_MODULE_ENABLED |
| #define | HSE_VALUE 8000000U |
| Adjust the value of External High Speed oscillator (HSE) used in your application. This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL). | |
| #define | HSE_STARTUP_TIMEOUT 100U |
| #define | HSI_VALUE 8000000U |
| Internal High Speed oscillator (HSI) value. This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL). | |
| #define | LSI_VALUE 40000U |
| Internal Low Speed oscillator (LSI) value. | |
| #define | LSE_VALUE 32768U |
| External Low Speed oscillator (LSE) value. This value is used by the UART, RTC HAL module to compute the system frequency. | |
| #define | LSE_STARTUP_TIMEOUT 5000U |
| #define | VDD_VALUE 3300U |
| This is the HAL system configuration section. | |
| #define | TICK_INT_PRIORITY 15U |
| #define | USE_RTOS 0U |
| #define | PREFETCH_ENABLE 1U |
| #define | USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ |
| #define | USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ |
| #define | USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ |
| #define | USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ |
| #define | USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ |
| #define | USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ |
| #define | USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ |
| #define | USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ |
| #define | USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ |
| #define | USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ |
| #define | USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ |
| #define | USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ |
| #define | USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ |
| #define | USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ |
| #define | USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ |
| #define | USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ |
| #define | USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ |
| #define | USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ |
| #define | USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ |
| #define | USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ |
| #define | USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ |
| #define | USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ |
| #define | USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ |
| #define | MAC_ADDR0 2U |
| Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code. | |
| #define | MAC_ADDR1 0U |
| #define | MAC_ADDR2 0U |
| #define | MAC_ADDR3 0U |
| #define | MAC_ADDR4 0U |
| #define | MAC_ADDR5 0U |
| #define | ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ |
| #define | ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ |
| #define | ETH_RXBUFNB 8U /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ |
| #define | ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ |
| #define | DP83848_PHY_ADDRESS 0x01U |
| #define | PHY_RESET_DELAY 0x000000FFU |
| #define | PHY_CONFIG_DELAY 0x00000FFFU |
| #define | PHY_READ_TO 0x0000FFFFU |
| #define | PHY_WRITE_TO 0x0000FFFFU |
| #define | PHY_BCR ((uint16_t)0x00) |
| #define | PHY_BSR ((uint16_t)0x01) |
| #define | PHY_RESET ((uint16_t)0x8000) |
| #define | PHY_LOOPBACK ((uint16_t)0x4000) |
| #define | PHY_FULLDUPLEX_100M ((uint16_t)0x2100) |
| #define | PHY_HALFDUPLEX_100M ((uint16_t)0x2000) |
| #define | PHY_FULLDUPLEX_10M ((uint16_t)0x0100) |
| #define | PHY_HALFDUPLEX_10M ((uint16_t)0x0000) |
| #define | PHY_AUTONEGOTIATION ((uint16_t)0x1000) |
| #define | PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) |
| #define | PHY_POWERDOWN ((uint16_t)0x0800) |
| #define | PHY_ISOLATE ((uint16_t)0x0400) |
| #define | PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) |
| #define | PHY_LINKED_STATUS ((uint16_t)0x0004) |
| #define | PHY_JABBER_DETECTION ((uint16_t)0x0002) |
| #define | PHY_SR ((uint16_t)0x10U) |
| #define | PHY_SPEED_STATUS ((uint16_t)0x0002U) |
| #define | PHY_DUPLEX_STATUS ((uint16_t)0x0004U) |
| #define | USE_SPI_CRC 0U |
| #define | assert_param(expr) |
| Include module's header file. | |
HAL configuration file.
Copyright (c) 2017 STMicroelectronics. All rights reserved.
This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.
Definition in file stm32f1xx_hal_conf.h.
| #define assert_param | ( | expr | ) |
| #define DP83848_PHY_ADDRESS 0x01U |
Definition at line 188 of file stm32f1xx_hal_conf.h.
| #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ |
Definition at line 180 of file stm32f1xx_hal_conf.h.
| #define ETH_RXBUFNB 8U /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ |
Definition at line 182 of file stm32f1xx_hal_conf.h.
| #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ |
Definition at line 181 of file stm32f1xx_hal_conf.h.
| #define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ |
Definition at line 183 of file stm32f1xx_hal_conf.h.
| #define HAL_CORTEX_MODULE_ENABLED |
Definition at line 72 of file stm32f1xx_hal_conf.h.
| #define HAL_DMA_MODULE_ENABLED |
Definition at line 45 of file stm32f1xx_hal_conf.h.
| #define HAL_DMA_MODULE_ENABLED |
Definition at line 45 of file stm32f1xx_hal_conf.h.
| #define HAL_EXTI_MODULE_ENABLED |
Definition at line 75 of file stm32f1xx_hal_conf.h.
| #define HAL_FLASH_MODULE_ENABLED |
Definition at line 74 of file stm32f1xx_hal_conf.h.
| #define HAL_GPIO_MODULE_ENABLED |
Definition at line 48 of file stm32f1xx_hal_conf.h.
| #define HAL_GPIO_MODULE_ENABLED |
Definition at line 48 of file stm32f1xx_hal_conf.h.
| #define HAL_MODULE_ENABLED |
This is the list of modules to be used in the HAL driver.
Definition at line 36 of file stm32f1xx_hal_conf.h.
| #define HAL_PWR_MODULE_ENABLED |
Definition at line 77 of file stm32f1xx_hal_conf.h.
| #define HAL_RCC_MODULE_ENABLED |
Definition at line 78 of file stm32f1xx_hal_conf.h.
| #define HAL_SPI_MODULE_ENABLED |
Definition at line 65 of file stm32f1xx_hal_conf.h.
| #define HAL_UART_MODULE_ENABLED |
Definition at line 68 of file stm32f1xx_hal_conf.h.
| #define HSE_STARTUP_TIMEOUT 100U |
Time out for HSE start up, in ms
Definition at line 91 of file stm32f1xx_hal_conf.h.
| #define HSE_VALUE 8000000U |
Adjust the value of External High Speed oscillator (HSE) used in your application. This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL).
Value of the External oscillator in Hz
Definition at line 87 of file stm32f1xx_hal_conf.h.
| #define HSI_VALUE 8000000U |
Internal High Speed oscillator (HSI) value. This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL).
Value of the Internal oscillator in Hz
Definition at line 100 of file stm32f1xx_hal_conf.h.
| #define LSE_STARTUP_TIMEOUT 5000U |
Time out for LSE start up, in ms
Definition at line 121 of file stm32f1xx_hal_conf.h.
| #define LSE_VALUE 32768U |
External Low Speed oscillator (LSE) value. This value is used by the UART, RTC HAL module to compute the system frequency.
< Value of the Internal Low Speed oscillator in Hz The real value may vary depending on the variations in voltage and temperature. Value of the External oscillator in Hz
Definition at line 117 of file stm32f1xx_hal_conf.h.
| #define LSI_VALUE 40000U |
Internal Low Speed oscillator (LSI) value.
LSI Typical Value in Hz
Definition at line 107 of file stm32f1xx_hal_conf.h.
| #define MAC_ADDR0 2U |
Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code.
Definition at line 172 of file stm32f1xx_hal_conf.h.
| #define MAC_ADDR1 0U |
Definition at line 173 of file stm32f1xx_hal_conf.h.
| #define MAC_ADDR2 0U |
Definition at line 174 of file stm32f1xx_hal_conf.h.
| #define MAC_ADDR3 0U |
Definition at line 175 of file stm32f1xx_hal_conf.h.
| #define MAC_ADDR4 0U |
Definition at line 176 of file stm32f1xx_hal_conf.h.
| #define MAC_ADDR5 0U |
Definition at line 177 of file stm32f1xx_hal_conf.h.
| #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) |
Auto-Negotiation process completed
Definition at line 213 of file stm32f1xx_hal_conf.h.
| #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) |
Enable auto-negotiation function
Definition at line 208 of file stm32f1xx_hal_conf.h.
| #define PHY_BCR ((uint16_t)0x00) |
Transceiver Basic Control Register
Definition at line 199 of file stm32f1xx_hal_conf.h.
| #define PHY_BSR ((uint16_t)0x01) |
Transceiver Basic Status Register
Definition at line 200 of file stm32f1xx_hal_conf.h.
| #define PHY_CONFIG_DELAY 0x00000FFFU |
Definition at line 192 of file stm32f1xx_hal_conf.h.
| #define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) |
PHY Duplex mask
Definition at line 221 of file stm32f1xx_hal_conf.h.
| #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) |
Set the full-duplex mode at 100 Mb/s
Definition at line 204 of file stm32f1xx_hal_conf.h.
| #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) |
Set the full-duplex mode at 10 Mb/s
Definition at line 206 of file stm32f1xx_hal_conf.h.
| #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) |
Set the half-duplex mode at 100 Mb/s
Definition at line 205 of file stm32f1xx_hal_conf.h.
| #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) |
Set the half-duplex mode at 10 Mb/s
Definition at line 207 of file stm32f1xx_hal_conf.h.
| #define PHY_ISOLATE ((uint16_t)0x0400) |
Isolate PHY from MII
Definition at line 211 of file stm32f1xx_hal_conf.h.
| #define PHY_JABBER_DETECTION ((uint16_t)0x0002) |
Jabber condition detected
Definition at line 215 of file stm32f1xx_hal_conf.h.
| #define PHY_LINKED_STATUS ((uint16_t)0x0004) |
Valid link established
Definition at line 214 of file stm32f1xx_hal_conf.h.
| #define PHY_LOOPBACK ((uint16_t)0x4000) |
Select loop-back mode
Definition at line 203 of file stm32f1xx_hal_conf.h.
| #define PHY_POWERDOWN ((uint16_t)0x0800) |
Select the power down mode
Definition at line 210 of file stm32f1xx_hal_conf.h.
| #define PHY_READ_TO 0x0000FFFFU |
Definition at line 194 of file stm32f1xx_hal_conf.h.
| #define PHY_RESET ((uint16_t)0x8000) |
PHY Reset
Definition at line 202 of file stm32f1xx_hal_conf.h.
| #define PHY_RESET_DELAY 0x000000FFU |
Definition at line 190 of file stm32f1xx_hal_conf.h.
| #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) |
Restart auto-negotiation function
Definition at line 209 of file stm32f1xx_hal_conf.h.
| #define PHY_SPEED_STATUS ((uint16_t)0x0002U) |
PHY Speed mask
Definition at line 220 of file stm32f1xx_hal_conf.h.
| #define PHY_SR ((uint16_t)0x10U) |
PHY status register Offset
Definition at line 218 of file stm32f1xx_hal_conf.h.
| #define PHY_WRITE_TO 0x0000FFFFU |
Definition at line 195 of file stm32f1xx_hal_conf.h.
| #define PREFETCH_ENABLE 1U |
Definition at line 134 of file stm32f1xx_hal_conf.h.
| #define TICK_INT_PRIORITY 15U |
tick interrupt priority (lowest by default)
Definition at line 132 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ |
Definition at line 136 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ |
Definition at line 137 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ |
Definition at line 138 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ |
Definition at line 139 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ |
Definition at line 140 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ |
Definition at line 141 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ |
Definition at line 142 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ |
Definition at line 143 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ |
Definition at line 152 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ |
Definition at line 144 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ |
Definition at line 145 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ |
Definition at line 146 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ |
Definition at line 147 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ |
Definition at line 148 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ |
Definition at line 149 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ |
Definition at line 150 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ |
Definition at line 151 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ |
Definition at line 154 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ |
Definition at line 153 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ |
Definition at line 155 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ |
Definition at line 156 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ |
Definition at line 157 of file stm32f1xx_hal_conf.h.
| #define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ |
Definition at line 158 of file stm32f1xx_hal_conf.h.
| #define USE_RTOS 0U |
Definition at line 133 of file stm32f1xx_hal_conf.h.
| #define USE_SPI_CRC 0U |
Definition at line 230 of file stm32f1xx_hal_conf.h.
| #define VDD_VALUE 3300U |
This is the HAL system configuration section.
Value of VDD in mv
Definition at line 131 of file stm32f1xx_hal_conf.h.
1.12.0